Jopower 9 Inch 96w Spot Headlights - off road lights Manufacturer
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV

JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV

The JOPOWER 9 Inch 96W spot headlights offer precise, durable illumination for multiple vehicles. Engineered by a trusted led off-road lights manufacture, they suit custom off road lights and professional off-road lights setups.

Brand
JOPOWER
Material
Aluminum die-cast housing
Waterproof rate
P67
Lifetime
50000H
Voltage
12-24V
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV
  • JOPOWER 9 Inch Car 96W Spot Headlights for boats ATV

Description

Product Overview

These 9-inch spot headlights are built around one job: putting a tight, long-reaching white beam exactly where the driver or skipper is already looking. Behind the lens sits a multi-LED array in its own reflector cups, so the light is collected and thrown forward as a spot instead of washing out across the ground just ahead of the vehicle. At 6000 K the output reads as crisp white, which keeps channel markers, fence posts and trail furniture distinct against a dark background.

The housing is die-cast aluminum alloy with a plastic outer cover finished in red, and the lens is clear PMMA with the LED array visible behind it. It is a compact, self-contained lamp with a bracket and a cable rather than a bar that needs a roof rack, which is why it turns up on things as different as a centre console, a quad and a service truck.

These are round offroad lights for truck, boat and trail use, with a wide spread of applications: the front of a centre-console boat, an ATV or UTV bar, a 4x4 bumper or roof rack, a flatbed work truck, or a yard machine that runs after dark. Most buyers take a pair for the front of the vehicle; a single unit works where one extra pool of distance light is all that is needed.

If you already run bars and work lights, these slot in as the long-throw element of a larger off road lights set and can be aimed independently of the bar's flood pattern. If you are building a first set, this is a simple place to start: one housing, one bracket, one cable, and a supply range wide enough to cover almost every vehicle on a dealer's lot.

LED off-road light pods and bars with factory and certification scenes.Company profile banner for Dongguan Spotlight Lighting with factory exterior and certifications.Manufacturing capability infographic with factory area, production lines, lab, and CNC workshop.Banner listing reasonable price, OEM service, free design, and ready stock.Service infographic showing LED automotive lighting products and customization options.Six-step customization process infographic with service icons.

Spot Beam & Build Advantages

  • Reach where it matters. The reflector cups concentrate the 96 W output into a narrow forward cone, so the next bend, marker or obstacle appears well before the near ground floods with light — the difference between driving to the limit of what you can see and driving to the limit of the lamp.
  • Sealed for wet, dusty work. IP67 covers water and dust ingress, which is what lets these led offroad lights sit on a bow rail through spray and on a quad through grit without the inside fogging or the contacts corroding.
  • A lens that survives gravel. Most off road lights fail at the front first. PMMA takes the chips and impacts that crack glass, and it passes light cleanly, so the beam stays sharp after a season of stones thrown up by a front tyre.
  • Heat handled by the housing. The die-cast aluminum body is the heat path away from the emitters, which is why the lamp holds its output through a long night run rather than fading once it is hot.
  • Built for temperature swings. Rated from -40 °C to 155 °C with up to 50,000 hours of service, it is designed for cold morning starts and hot, vibration-heavy work rather than occasional weekend use.
  • Compact round footprint. A 9-inch round body fits bull bars, roof racks and console brackets where a long bar will not go, and a pair of 4x4 off-road lights sits neatly either side of a winch or a chart plotter.

Fitment & Voltage Compatibility

Any vehicle with a 12 V or 24 V DC system and a flat mounting surface will take this lamp: cars, pickups, SUVs, ATVs, UTVs, side-by-sides, boats and most plant machinery. Because the input range runs from 9 to 32 V DC, the same unit works whether it is wired as led driving lights on a road car or as an auxiliary lamp on a boat, and it keeps working while alternator voltage swings during a long run.

On a pickup or flatbed they are usually fitted as offroad lights for truck work — early starts, yard manoeuvring, winter roads — on the bumper, the bull bar or a headache rack. Run the supply through a relay and a switch rated for the current, keep the cable clear of exhaust and manifold heat, and use the supplied bracket rather than drilling the housing.

Aim matters as much as position on 4x4 off-road lights. A spot beam set dead ahead lights a long corridor but leaves the ground directly in front of the tyres dark, so if you drive tight trails, angle the pair slightly outward and let a flood or combo unit handle the near field.

Buyers building a full array often sketch the custom off road lights layout before drilling anything: one spot pair for distance, one wider unit for the sides, and a switch panel that lets the driver choose between them. These lamps are designed to be one element of that set rather than the whole of it.

On an ATV or UTV, check the lamp clears the handlebars or cage on full lock and full suspension travel before you drill, and mount it behind rather than in front of a brush guard that could push the lamp back into the bodywork.

- Night navigation on the water. Mounted above the spray line on a centre console or open boat, a pair picks out channel markers, mooring buoys and unlit hulls well beyond the reach of a standard deck light, and the sealed body copes with salt spray and rain. - ATV and UTV trail riding. On a front bar or cage, these round offroad lights throw a corridor of white light down the trail while the machine's own headlights handle the near ground — useful on wooded tracks where the next bend arrives fast. - 4x4 and overland travel. For 4x4 off-road lights the spot pattern is the distance element: mount a pair on the bumper or rack, aim them down the track, and leave the near field to a flood or combo bar so you get both reach and width. - Work trucks and site vehicles. On a flatbed, tipper or service truck, a spot pair lights the far end of a yard, a gate or a loading bay without glare bouncing back off the cab. Buyers specifying offroad lights for truck fleets usually fit one pair per vehicle and standardise on a single part number. - Rescue, utility and farm machines. Tractors, telehandlers and utility vehicles often work in the dark in fields and yards with no fixed lighting, and one part number covers a 12 V pickup and a 24 V machine on the same site. - Resale and accessory bundles. Shops building a lighting package for custom lights for trucks put a spot pair next to a bar, a switch panel and a wiring kit, so the customer leaves with a complete set rather than one lamp and a question.

Specifications

ModelJOPOWER 9-inch spot headlight
Power96 W
Beam patternSpot
Size9 inch
HousingDie-cast aluminum alloy
Outer coverPlastic, red
LensPMMA
Operating voltageDC 9-32 V
Color temperature6000 K
Waterproof and dust ratingIP67
Working temperature-40 °C to 155 °C
Rated service life50,000 hours
MountingBracket supplied, wired connection

Mounting & Installation

  1. Choose the mounting point. Pick a flat, rigid surface behind or above the intended beam line — bumper, bull bar, roof rack, console top or cabin roof — and check the lamp clears bodywork, the wiper arc and any steering or suspension movement.
  2. Offer the bracket up and mark the holes. Hold the supplied bracket against the surface, check the lamp sits level, and mark the fixing points before drilling. Use a backing plate where the panel is thin or the surface is gelcoat.
  3. Bolt the bracket down first. Fix and tighten the bracket, then hang the lamp on it, so you are not holding the weight of the light while you line up the mounting bolts.
  4. Wire through a fused relay and a switch rated for the load. Earth the lamp to clean bare metal on the chassis and keep the cable run clear of exhaust, manifold and moving parts.
  5. Aim it before you finish. Park on level ground facing a wall, switch on, and set the spot cone where you actually need it — straight down the track for 4x4 off-road lights used on open ground, or slightly outward for tight trail work. Tighten the bracket once the aim is right.
  6. Check the seals and re-check after the first trip. Confirm the lens cover sits flush and the cable entry is sealed, then re-torque the bracket bolts after the first long drive or the first rough water, when vibration has settled everything in.

Care & Maintenance

Cleaning is the whole routine. Rinse the lens with fresh water after saltwater use, wipe dust off before a night run, and skip solvents and pressure washers held close to the seal — petrol, thinners and a hard jet will cloud a PMMA lens and can push water past a gasket that was doing its job.

Once a season, look at the parts that fail first: the terminals for green corrosion, the cable where it passes through a panel for chafing, the bracket bolts for looseness, and the seal line for condensation behind the lens. A smear of dielectric grease on a clean terminal keeps moisture out, and re-torquing the bracket after the first long trip stops the aim drifting. With a sealed body and no glass to break, these led offroad lights need those checks once or twice a year rather than a maintenance schedule.

Keeping the lens clean does more for output than anything else you can do — a dust film scatters light and shortens the throw noticeably. A soft cloth and clean water before a night run is the biggest single factor in keeping led driving lights performing the way they did on day one, and it takes a minute.

Customization & Branding

  • Your logo on the lamp and the carton. Artwork goes on the cover, the packaging or both, working from your files rather than a fixed template, so the unit arrives looking like your product rather than ours.
  • Colour and finish to your range. The red cover is standard; other colours can be specified alongside style and size changes, which is how shops build custom off road lights that match a brand palette instead of a catalogue page.
  • Specification and bracket detail. Tell us the vehicle, the mounting surface and the cable run, and the specification, style and size can be set to suit rather than trimmed to fit afterwards.
  • Packaging built for the shelf or the pallet. Shelf-ready cartons with your print, plain bulk packing, or a mix across one order — the layout is agreed before production.
  • One shipment, full range. Spot headlights, light bars, work lights and switch panels travel together, so a reseller ordering custom lights for trucks alongside bars does not have to split a lighting range across several suppliers.

Ordering & Delivery

Stock items move on a 7-day fast shipping schedule, which is what lets most resellers reorder a pair without holding deep stock. Custom work — logo, packaging, colour or a different specification — starts after artwork approval, so factor that approval stage into your timeline when you order custom lights for trucks under your own brand.

Payment terms, carton quantities and packing format are confirmed per order rather than published on a page: tell your sales contact the destination, the quantity and whether the cartons need to be shelf-ready or bulk packed, and the terms come back in writing before production starts. Ask about current sample availability and the lead time for the quantity you need.

If your listing, tender or import paperwork needs the exact figures in writing — power, supply range, sealing rating, certification files for your market — request the current specification sheet for the batch you are ordering and check it against the details here before you commit.

Scale & Supply Capability

JOPOWER is the brand of our own factory in Dongguan, China, founded in 2010 and run by a team of 20–30 people with 15 years of vehicle lighting production behind them. We add 5–10 new styles every month, hold EU, CE, RoHS and US DOT certification, and put every unit through three full inspections before it leaves us. Because the designs are developed in-house, we can tailor specification, style, size, color, logo and packaging, and items in stock ship in as little as 7 days.

FAQ

What materials are used in these spot headlights?

The body is die-cast aluminum alloy, the outer cover is a plastic shell finished in red, and the lens is PMMA rather than glass. That combination matters in practice: the aluminum carries heat away from the emitters and holds its shape under vibration, the plastic cover takes knocks without denting, and PMMA passes light cleanly while resisting the chips that crack glass.

Can the lights be customized for different vehicles?

The 9-32 V DC input already covers most vehicle types, from a 12 V ATV or outboard to a 24 V truck or machine. Beyond that, we build custom off road lights to order: specification, style, size, colour, logo and packaging can be set for a specific vehicle program or a resale range. Tell us what the vehicles are and how the lamp will be mounted, and we will confirm the bracket and cable arrangement that suits.

How do I install these on my off-road vehicle?

Bolt the supplied bracket to a flat, rigid surface — bumper, bull bar, roof rack or console — with a backing plate where the panel is thin, then hang the lamp on the bracket. Earth to clean bare metal and keep the cable away from exhaust heat. The two mistakes that cause most problems are mounting to unsupported panel that flexes at speed and running the feed without a fused relay. Once it is on, aim the spot cone against a wall at night and confirm the lens cover and cable entry are sealed. No converter is needed on a 12 V or 24 V system, which makes the same routine work for any off road lights you fit alongside these.

What maintenance do the headlights need?

Very little. Rinse the lens with fresh water after saltwater use, wipe dust off before a night run, and keep solvents and high-pressure jets away from the seal. Once a season, check the terminals for corrosion, look for chafing where the cable passes through a panel, and re-torque the bracket bolts. Because the body is sealed and the lens is PMMA, these led offroad lights do not need anything beyond those checks.

Is a spot beam too narrow for trail riding?

A spot pattern is deliberately narrow so the light reaches further, which is exactly right for seeing the next bend or marker — but it leaves the ground immediately in front of the vehicle darker than a flood does. Most trail and overland buyers run a spot pair for distance and a flood or combo bar for the near field so the two patterns overlap. Used that way, these work well as long-range led driving lights rather than as the only lamp on the vehicle.

Will they work on a 24 V truck or machine?

Yes. The input range is 9-32 V DC, so the same lamp runs on a 12 V car, ATV or boat system and on a 24 V truck, bus or plant machine without a converter or a second part number. That is the main reason mixed fleets, and shops that sell offroad lights for truck and machine applications, can carry one line instead of two.

Are these suitable for saltwater use on a boat?

IP67 covers spray and rain, and neither the aluminum body nor the PMMA lens rusts or clouds the way steel and glass can. What matters most is the mounting position: keep the lamp above the spray line so it deals with splash rather than sitting in standing water, and fit it to solid laminate or a backing plate rather than thin gelcoat. Round offroad lights like these are commonly fitted to centre consoles and open boats for exactly that job.

CONTACT US

If you have any queries, get in touch today! Don't hesitate. We try to take the extra step for our customer satisfaction.
Name *
Email *
Phone / Whatsapp
Message *
Verification code *
Click to verify