RGB LED Light Bar

RGB Bar Sizing & Fitment Selector

RGB LED Light Bar

RGB Bar Sizing & Fitment Selector

Six lengths, one decision. This selector turns the 8 / 14 / 20 / 32 / 43 / 55 inch range into a fitment plan you can send straight to a quote — match the bar to your vehicle class, match the bracket to your mounting surface, then confirm the control setup. Whether you are specing an rgb led light bar across a roof rack, or comparing an rgb off road light bar for a bumper or rear chase mount, every module below ends in a figure you can ask us to confirm instead of a guess.

  • 01 Choose the length that matches your mounting surface
  • 02 Check bracket reach, rack spacing and wind load
  • 03 Confirm the 12–24V control setup and your quantity
RGB LED Light Bar 8/14/20/32/43/55 Inch Universal Off Road Driving Work Light

Start with length: which bar suits your mount

The six lengths cover everything from a compact bumper fit to a full roof-rack span. Read the table by mounting location first, then check the vehicle class in the same row — the bar that suits a UTV cage is rarely the bar that suits a full-size pickup roof. Width across the mount decides the length; the vehicle decides the bracket.

Length ranges are fitment guidance only — confirm beam pattern and output on the spec sheet before ordering.
RGB LED light bar lengths compared for bumper, roof rack and chase mounting
Six lengths, from 8 inch bumper bars to 55 inch full-width roof bars.
Length Typical mounting location Typical vehicle class Confirm before ordering
8 inch Front bumper, hood edge, A-pillar, rear chase add-on UTV, ATV, side-by-side, compact 4x4 Bracket reach against the hood curve and near-field beam coverage
14 inch Front bumper, lower grille, hood 4x4, mid-size SUV, van Grille opening width and clearance around winch or tow points
20 inch Bumper, front rail of a roof rack, light bar hoop 4x4, SUV, pickup Rack bar spacing and the bracket footprint on the rail
32 inch Roof rack, windshield-top mount, full-width bumper Pickup, full-size SUV, van, fleet vehicles Roof width plus wind load at highway speed
43 inch Roof rack, bed rack, full-width bumper Full-size pickup, 4x4 wagon, commercial fleet Total rack span and how much the body twists on rough ground
55 inch Full-width roof rack, headache rack, van and truck roof Heavy pickup, van, truck, agricultural and utility vehicles Roof curvature, mounting foot positions and the harness route

12–24V wiring, stable current and the control setup

The bar is built around a 12–24V wide voltage range, so one unit covers a 12V truck system and a 24V commercial, agricultural or utility machine. Stable-current circuitry is described as holding brightness steady rather than fading as voltage moves. Get the electrical questions settled at quote stage, not at install stage.

  • Voltage range12–24V, which lets a mixed 12V and 24V fleet run the same bar.
  • Current stabilityOutput is described as consistent rather than fading as supply voltage drifts.
  • InterferenceThe product page states no electromagnetic interference with vehicle electronics — ask us to confirm test conditions alongside radios, GPS and dash-cams.
  • ControlWhich controller or switch panel drives the RGB channels is not published on the product page. Tell us what you already run and we will confirm the pairing with your quote.
RGB off road light bar wired for a 12 to 24 volt vehicle electrical system
One 12–24V unit covers mixed-voltage fleets, so stock planning stays simple.
Sealed rugged housing and heat-managed body of the RGB LED light bar
Sealed housing, thermal management and modular brackets are the three durability claims on the page.

IP68, thermal management and what to confirm in writing

IP68 sealing, a rugged housing and thermal management matter on any bar that lives outdoors. Turn each claim into something your purchasing file can hold before the order is placed.

  • SealingIP68 is listed for rain, snow, dust and temporary submersion — ask for the depth and duration behind the rating if the vehicle works flooded ground or coastal routes.
  • ThermalThe housing is described as managing heat to protect output and service life — ask how brightness holds through a long night run.
  • Housing and bracketsA rugged housing with modular adjustable brackets is specified for vibration and impact — ask for bracket material and bolt torque.
  • EnvironmentFor winter-road or marine use, ask how the finish is expected to handle salt spray.
Buyer decision: put the answers in the quote request so the specification you approve is the specification you receive.

Specification snapshot

The published figures that drive the fitment decision, plus the values we confirm with your quote so nothing is assumed at the install.

Light colourRGB colour-changing output
Available lengths8 / 14 / 20 / 32 / 43 / 55 inch
Voltage12–24V wide voltage range with stable current technology
Waterproof ratingIP68 — rain, snow, dust and temporary submersion
MountingAdjustable mounting brackets, modular mount design, roof rack mount
Compatibility4x4, UTV, ATV, truck, SUV and car roof rack mounting
Also specified forOff-road vehicles, trucks, boats, industrial applications, utility, agricultural and emergency vehicles
RGB customisationSupports branding and specialised signalling applications
Confirmed at quoteWattage, lumens, LED count, beam pattern, colour temperature and warranty terms

Send three details, get a size-based quote

There is no published price list because every bar is configured to the build: length, bracket and control hardware all move with the vehicle. Give us the three answers below and we will come back with a length, a bracket recommendation and your quote.

  • 01 — Vehicle and mounting surface

    Make, model and whether the bar goes on a roof rack, front bumper, hood, A-pillar or rear chase.

  • 02 — Width and bracket clearance

    Rack span or grille opening in millimetres or inches, plus anything already mounted there — winch, sensors, roof box.

  • 03 — Quantity and control setup

    Single unit, fleet batch or an OEM run, and the controller or switch panel you plan to use for the RGB channels.

RGB LED light bar configured for custom length and OEM branding requests

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

How to Choose an RGB LED Light Bar Manufacturer for Wholesale

Choosing an RGB LED light bar manufacturer for wholesale begins with size coverage, certification scope, factory testing, and a clear inquiry brief.

Read article

Preparing an OEM Inquiry for Custom RGB LED Light Bars

An OEM RGB light bar program moves faster when the brand team defines the size line, logo files, packaging direction, and target market before the first factory discussion.

Read article

12-24V Wide Voltage and Low EMI in Off Road LED Light Bars

A light bar’s voltage range and driver design decide whether it simply lights up or behaves predictably around the rest of a vehicle’s electronics.

Read article

Frequently Asked Questions

What information is shown for this product?

Review the product details, images, and specifications presented on the official product page.

Where can I check the intended application?

Use the application and use-case information published on the official product page.

Which specifications should I confirm before ordering?

Confirm the specifications and options listed for the exact product variant before placing an order.

Where can I check available options?

Check the official product page or ask the supplier about options shown for the selected product.

How can I request product information?

Use the official contact or inquiry path provided on the site.

What should I include in an inquiry?

Include the product page, intended use, required quantity, and any specifications you need the supplier to review.