Fields, yards and farm tracks are hard on lighting, and a tractor working after dark needs something different from a road lamp. What the operator has to see is the ground about to pass under the wheels and the implement about to be lifted, not a bright point somewhere near the horizon. This 36W, 4.5-inch round work light is built around that job: a sealed, die-cast lamp with a flood pattern that lays a broad, even sheet of white light over the working area in front of or beside the machine. A pivoting bracket lets the beam drop close to the wheels for loader and hitch work, or lift to cover a wider strip when the machine is moving along a track. Inside, the LEDs sit on a board screwed into the aluminum body, so heat leaves through metal rather than through a plastic shell. We supply this lamp mainly to farm equipment dealers, parts counters and workshops that fit lighting for agricultural customers, and to estates and yards that keep their own machines working at night. It replaces the round work lamps fitted to older cabs, loader arms and implement frames, with the same bolt-on mounting idea and none of the bulb changes. We are LED light bar manufacturers by trade, and this lamp comes off the same lines with the same sealing and test routine. If your counter already sells LED offroad lights for road vehicles, it is the agricultural sibling: same construction, same bracket logic, a beam chosen for the ground rather than the distance. Stock it beside the LED driving lights for customers running mixed fleets, and the buyer who needs one of the three usually needs the others. - Flood pattern built for ground work — the spread covers the strip the machine is working and the implement in front of or behind it. It is the opposite of the narrow pencil beam that most off road lights for highway use are designed to throw, and it is why an operator can read a swath edge or a bucket corner without turning the machine. - Die-cast aluminum housing — a rigid cast body keeps the lens flat against its seat and stops the mounting ears flexing when the machine works over ruts and headlands. - Sealed against dust, rain and wash-down — the lamp is built for the cycle a farm machine lives in: mud and dust in the field, a wash-down at the end of the day, then a cold night. - Heat managed by the body itself — the board is fixed to the aluminum housing and the back is finned, so heat leaves the LEDs through metal; overheat protection is built in for long evenings. - Long service life — with no filament to burn out, the lamp is normally replaced with the machine rather than with the season, which matters when a failure means stopping a job in the dark. - Adjustable-angle bracket — slacken two bolts, aim, tighten. One bracket covers a close working angle for loader and hitch work and a flatter angle for travel. - Plug-and-play wiring loom — the lead ends in a connector rather than bare wires, so fitting is a wiring job, not a soldering job. - Same round footprint as what it replaces — the round format and bracket style are the ones used on 4x4 off-road lights and on the halogen work lamps already fitted to many cabs, so existing mounting holes often line up.





Farm machinery is a hard place for a lamp: dust in the lens, mud on the housing, a pressure washer at the end of the day, then frost overnight. The LEDs sit on a circuit board screwed into the die-cast aluminum housing rather than pressed into a plastic shell. Metal-to-metal contact gives heat a short path out of the board, and it means the housing does more than hold the shape — it works as the heat sink. Fins across the back add surface area so heat leaves the lamp while it runs, which keeps output steady through a long evening instead of fading once the lamp warms up. Overheat protection is built in for the nights when a lamp stays on for hours. The lens, high-transmission polymer or tempered glass depending on the build, is seated against the housing face so the beam leaves cleanly and water runs off rather than sitting on the seal. The sealed body is rated against dust and water, which covers rain on a cab roof, wash-down water and the condensation that forms when a warm lamp meets a cold night. Three habits keep a sealed lamp healthy. Do not hold a high-pressure jet directly against the lens edge or the gasket line. Do not leave the lamp submerged. And wipe mud, slurry and fertiliser residue off the housing after a session, so the fins stay clear and can do their job. As LED light bar manufacturers we hold the test records, so if your listing, tender or customer needs the sealed rating confirmed in writing for a particular batch, ask us and we will put the tested figure on paper before you publish it.
| Product type | Round LED work light, flood beam |
| Rated power | 36 W |
| Input voltage | 12-24 V DC |
| Beam pattern | Flood |
| Housing | Die-cast aluminum |
| Lens | High-transmission polymer or tempered glass |
| Sealing | IP67 |
| Rated life | 50,000 hours |
| Operating temperature | -40 °C to +85 °C |
| Mounting | Adjustable-angle bracket |
| Connection | Plug-and-play wiring assembly |
| Typical fitment | Tractors, loaders, telehandlers, combines, trailers, trucks, SUV, ATV, UTV |
| Dispatch | 7-day fast shipping |
| Order quantity | Confirmed with your sales contact for each order |
| Customization | Specification, style, size, color, logo and packaging for custom off road lights programmes — as LED light bar manufacturers we build to your brief, not just to our own catalogue |
| Artwork approval | Logo and colour signed off before production starts |
| Packing | Standard carton as shipped; branded cartons to your artwork |
| Range on one order | Work lights, whip lights, switch panels and LED light bars |
| Matching lights | LED driving lights and fog lights from the same range |
| Certification | CE, RoHS and US DOT, as stated for our production |
| Sealed rating | IP67 on our specification sheet; confirm the tested figure for your batch before printing |
| Warranty | Ask your sales contact for the current terms in writing |
| Samples | Ask your sales contact about availability and cost |
| Lead time | Confirmed with your sales contact when the order is placed |
| Contact | Paul, +86 15362436281 (call or WhatsApp) · Szvictory2005@163.com |
JOPOWER is the brand of our own factory in Dongguan, China, founded in 2010 and run by a team of 20–30 people with 15 years of vehicle lighting production behind them. We add 5–10 new styles every month, hold EU, CE, RoHS and US DOT certification, and put every unit through three full inspections before it leaves us. Because the designs are developed in-house, we can tailor specification, style, size, color, logo and packaging, and items in stock ship in as little as 7 days.
